Loading...
Loading...
Materials properties, battery data, semiconductor, alloys, polymers, additive manufacturing
813 datasets
A figshare admin karger published a case report on April 15, 2026, detailing the treatment of a 20-year-old male patient with severe anti-glomerular basement membrane disease. The 22.4 KB document describes the patient's clinical presentation, treatment with plasmapheresis, corticosteroids, cyclophosphamide, and adjunctive Obinutuzumab, and subsequent renal recovery over a 5-month follow-up.
NDI Carrara 1 is a 1751-meter stratigraphic drill hole completed in 2020, intersecting ~625 meters of Paleozoic and ~1120 meters of Proterozoic rock. Geoscience Australia presents new high-resolution strontium (87Sr/86Sr), carbon (δ13C), and oxygen (δ18O) isotope data from carbonate samples to understand paleo-depositional environments and chemostratigraphy. The data was presented at the 2023 Australian Earth Science Convention.
Experimental data from a study on cross-linked polyethylene oxide membranes for gas separation. The dataset includes measurements of CO2 permeability and CO2/H2 separation coefficients for original and PEG-impregnated membranes, with results showing significant performance improvements. The data was authored by Shanshan Ji and last updated on 2026-04-10.
Fluorescence imaging data from genetically encoded nanoparticles used to measure cytoplasmic viscosity in colorectal cancer cell lines. The dataset likely contains diffusion coefficients and viscosity estimates derived from differential dynamic microscopy analysis. The data was uploaded by Steven Huysecom to figshare in April 2026.
Australia's 721 clastic coastal depositional environments were statistically assessed for wave, tide, and river power to test geomorphic predictability. The geomorphic classification, including deltas, estuaries, and tidal flats, was independently established from remotely sensed imagery. This analysis, from Geoscience Australia, represents a systematic numerical approach not previously attempted for any region on Earth.
Geoscience Australia provides conceptual geomorphic models derived from aerial and satellite imagery. These models are designed to help environmental managers assess sediment trapping, turbidity, water circulation, and habitat change along clastic coasts. The dataset was last updated on 2026-04-30.
A study by Modupeola Dada of Tshwane University of Technology investigates laser additive manufacturing of AlCoCrFeNiCu and AlTiCrFeCoNi high entropy alloy coatings. The research examines the influence of laser power (1200-1600 W) and scan speed (8-12 mm/s) on microstructure, hardness, and coating geometry. Results indicate defect-free structures with homogeneous adhesion to a mild steel substrate at a preheat temperature of 400 °C.
Nine carbon- and aluminium-based nanomaterials synthesized by hydrodynamic cavitation between 2019 and 2020 are characterized in this dataset. Raw data includes Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), Energy Dispersive X-ray Spectroscopy (EDS), and X-ray Diffraction (XRD) files. A Python script is provided to reproduce the fractal analysis, which found the effective fractal dimension for all materials converges around D = 1.8868.
Upper Cambrian-Lower Ordovician lithofacies data for the Ninmaroo Formation in the Georgina Basin, describing ooid, peloid, skeletal, and dolostone sequences. The dataset likely contains information on depositional environments, cyclic sedimentation patterns, and regressive sequences. It is hosted by the Australian Ocean Data Network and was last updated on 2026-04-16.
Topographic relief data from seabed mapping surveys on the Van Diemen Rise in the eastern Joseph Bonaparte Gulf. The dataset resulted from a joint Geoscience Australia and Australian Institute of Marine Science survey conducted in 2009 and 2010, collecting geological and biological data across four study areas from the outer to inner shelf. It provides context for the benthic biodiversity of the Arafura-Timor Sea and wider northern Australian marine region.
A geological study of the Permian Yessabah Limestone formation in the Manning-Macleay Basin of eastern Australia. The dataset, provided by the Australian Ocean Data Network, describes the depositional sequence, facies associations, and dominant faunal assemblages of crinoids and bryozoa within this thick crinoidal limestone unit. It was last updated on 2026-04-10.
Experimental results compare three slicing algorithms for additive manufacturing, applied to a ship model, vase model, and dice model. The dataset contains measurements, likely surface roughness, from printed models tested with a roughness meter. Xingguo Han published the data on figshare in April 2026.
Experimental results of dice, ship, and vase models printed using a six-degree-of-freedom additive manufacturing device. Data compares the performance of three slicing algorithms, including a proposed adaptive hierarchical method, with surface roughness measurements. Xingguo Han published this dataset on figshare in 2026.
Experimental results compare surface roughness from three different slicing algorithms applied to 3D printed models, including a vase, a ship, and dice. The data, approximately 5.5 KB in an XLS file, was published by Xingguo Han in April 2026. It supports research into optimizing fused deposition additive manufacturing processes.
Experimental data from Xingguo Han's 2026 research on an adaptive hierarchical slicing algorithm for fused deposition additive manufacturing. The dataset contains parameters and roughness measurements from models printed on a six-degree-of-freedom AM device. It compares the performance of equal thickness, normal vector-based, and the proposed contour-based slicing algorithms.
Experimental roughness data from three 3D printed models (ship, vase, dice) produced by a six-degree-of-freedom additive manufacturing device. Xingguo Han published this dataset on figshare in 2026 to compare the performance of different slicing algorithms. The 5.5 KB XLS file contains results from testing with a roughness meter.
Experimental results compare three slicing algorithms for Fused Deposition Modeling on ship, vase, and dice models. The dataset contains measured surface roughness data from prints produced by a six-degree-of-freedom additive manufacturing device. Xingguo Han published this data on figshare in April 2026.
Experimental data compares three slicing algorithms for additive manufacturing: equal thickness, adaptive based on triangular facet normals, and a novel adaptive hierarchical method. Results include surface roughness measurements from models printed on a six-degree-of-freedom AM device. The dataset was created by Xingguo Han and published on figshare in 2026.
Experimental data supports a new adaptive hierarchical slicing algorithm for fused deposition additive manufacturing. The 16.7 KB dataset contains results from slicing ship, vase, and dice STL models and measuring printed surface roughness. Xingguo Han published the data on figshare in April 2026.
Experimental data compares three slicing algorithms for fused deposition additive manufacturing. The dataset contains results from printing and testing ship, vase, and dice models on a six-degree-of-freedom AM device. Xingguo Han published this data on figshare in April 2026.